Rare, slow but impressive: > 43 ka of rockslide in river canyon incising crystalline rocks of the eastern Bohemian Massif

1705 Landslides 20 • (2023) Landslides (2023) 20:1705–1718 DOI 10.1007/s10346-023-02062-2 Technical Note Received: 6 December 2022 Accepted: 19 March 2023 Jan Lenart · Martin Kašing · Tomáš Pánek · Régis Braucher · František Kuda Rare, slow but impressive: > 43 ka of rockslide in river canyon incising crystalline rocks of the eastern Bohemian Massif Abstract Despite significant progress in understanding the stability of rock slopes, little is known about the time scales of the evolution of slow-moving rockslides. The Ledové sluje rockslide in the Thaya River canyon is a unique and infrequent slope failure developed in crystalline rocks of the Variscan orogen in Central Europe. Fresh topography with trenches, rock walls, slided blocks, scree slopes and crevice-type caves has attracted generations of geologists for more than a century, but questions of mechanism and age of the rockslide have remained unresolved. To address this question, we combined geomorphological research with detailed analysis of the geological structure, electrical resistivity profiling and terrestrial cosmogenic nuclide dating (TCN). Our data show that failure developed above the river undercut bank along a planar sliding surface predisposed by NW-oriented gently dipping metamorphic foliation intersected by steep fractures and faults. Although TCN dating does not allow determination of the entire life span of the rockslide, its scarp predisposed by NEto ENEstriking fault was largely exposed in the Last Glacial during marine isotope stages (MIS) 3 and 2 between ~ 43 and 23 ka, suggesting slow gradual or multievent movement of the rockslide slope rather than a single catastrophic event. We conclude that, although very rare in Central Europe, rockslides in the crystalline rocks of the Palaeozoic orogens may leave a much longer topographic footprint than in the adjacent Alpine mountain belts. Keywords Crevice-type cave · Electrical resistivity tomography · Orthogneiss · Structural analysis · Terrestrial cosmogenic nuclide dating Introduction Rockslides developed in crystalline rocks are commonly described from world mountain belts such as the European Alps (Strauhal et al. 2017; Zangerl et al. 2010), Carpathians (Němčok 1972; Pánek et al. 2016, 2017) and High Asia (Schramm et al. 1998; Weidinger and Korup 2009), but they are less common in pre-Cenozoic orogens, except in areas where topography has been rejuvenated by Quaternary glaciations or river incision (Jarman 2006; Ballantyne et al. 2014; Hilger et al. 2018; Böhme et al. 2019). In Europe, this is partly due to the lower topographic relief and less intensive rockslide triggers (e.g. seismicity, river incision) offered by the Palaeozoic mountain belts compared to the Cenozoic alpine ranges. The declining potential to produce large slope instabilities with mountain range lifetimes is termed “stress hardening” (Jarman 2006). This phenomenon is the result of long-term erosion, which gradually removes unstable volumes of rock, and the topography of the mountains is then more in equilibrium with the geological structure. In such areas, rockslides cluster mainly in rejuvenated, more recently cut river valleys or within the youngest glacial breaches (Jarman and Harrison 2019). However, the interpretation of the origin of these rockslides in the context of landscape evolution has so far been hampered by minimal knowledge about their onset and lifespans. Only for a small number of slow-moving rockslides the length of their evolution has been estimated (Schwartz et al. 2017; Böhme et al. 2019; Hilger et al. 2021; Břežný et al. 2021), and no such data exist for Palaeozoic highlands of Central and Western Europe situated outside the Pleistocene ice limits. In the crystalline domains of the Bohemian Massif formed by plutonic and metamorphic rocks (Fig. 1), rockslides are extremely rare, in contrast to the sedimentary and volcanic parts of the area (Migoń et al. 2017; Raška et al. 2016). In the Czech part of the Bohemian Massif, only single cases of rockslides in crystalline rocks have been inventoried, exclusively from mountains glaciated during the Last Glacial Maximum (Hartvich and Mentlík 2010), from tectonically more active parts of the area, such as the flanks of the Eger Rift (Burda et al. 2018), or from deeply incised river valleys (Zvelebil et al. 1996). The last group mainly includes river valleys incised to the eastern marginal slope of the Bohemian Massif at the contact with the Alpine–Carpathian foredeep. Although these valleys are only the first few hundred metres deep, they often have steep rock slopes and resemble canyons (Ivan and Kirchner 1994). Several rockslides from these valleys have been described by Hrádek (1998); however, information on their kinematics and chronological time frames is completely lacking. The present study reveals the predispositions, structure, mechanism and age of the Ledové sluje rockslide (LR), which is some of the most distinct rockslides originating within the nonglaciated Variscan orogenic belt in southeastern Czechia, Central Europe. The rockslide is unique with its remarkably well-preserved morphology as well as accessible internal structure through distinctly developed crevice-type caves (CTCs). Although this rockslide has been studied for more than a century (Filek 1895), there are still controversies regarding its predisposition, triggers, mechanism of movement and especially its age (Špalek 1935; Demek 1996; Kopecký 1996; Zvelebil et al. 1996). The main goal of this study was (i) to reveal the structural control of the rock massif through structural and geophysical data analyses, (ii) to assess the types of mass movements that formed the studied rockslide and (iii) to present the results of terrestrial cosmogenic nuclides dating outlining the minimum age of the rockslide. Published online: 26 April 2023 © The Author(s) 2023 1706 1706 Landslides 20 • (2023) Technical Note Combining these approaches, we demonstrate for the first time the long-term evolution of rockslide in the Variscan part of Europe. Regional settings Corresponding to the front of the Variscan collisional belt, the eastern margin of the Bohemian Massif is composed of three main tectonically stacked Precambrian and Palaeozoic crystalline complexes. In the W‒E direction, the Moldanubicum complex is thrust over Moravicum, and both complexes are jointly thrust over Brunovistulicum (Dudek 1980; Schulmann et al. 1994). Devonian limestones sandwiched between the Brunovistulicum basement and Moravicum complex indicate the Variscan tectonics of the area, more accurately a Lower Carboniferous age of the main tectonic phase (Dallmeyer et al. 1994). Within the Moravicum domain, two tectonic windows — the northern Schwarzawa window and the southern Dyje window — were formed (Suess 1912). In the latter, the Ledové sluje rockslide is located (Fig. 1). The Dyje window (dome), more precisely the tectonic half-window, consists of the lower inner phyllite unit (Suess 1912; Batík 1993) exposing mainly metapelites, gneiss, quartzites and marbles and the higher Bíteš gneiss nappe unit. It contains strongly deformed leucocratic orthogneiss with an expected Cadomian (Late Proterozoic–Cambrian) age, penetrating a varied metasedimentary succession of the outer phyllite unit (Schulmann et al. 1994). LR is situated in the Znojmo Highland, i.e. a slightly undulating landscape of the Bohemian Massif on the border between Czechia and Austria (Kopecký 1996). Even though the mean altitude of the Znojmo Highland does not exceed 365 m, the southeastern marginal slope of the Bohemian Massif is deeply incised by the Thaya (Dyje Cze.) River and other rivers flowing into the adjacent Alpine–Carpathian foredeep. The resulting canyons with often rocky steep slopes reach depths greater than 200 m. Morphotectonic evolution of the area was influenced by the proximity of the Diendorf-Čebín Fault Zone (DCFZ) (Roštínský et al. 2013) (Fig. 1). Manifesting as an ~ 200-km-long NE–SW-trending fault system of predominantly normal and strike-slip character, the DCFZ represents surface expression of the Variscan suture between the Moldanubicum and Brunovistulicum complexes with assumed tectonic activity in the Quaternary (Špaček et al. 2017). The LR site is situated in the western part of the Thaya River canyon, 40 km upstream from the outlet of the river into the Alpine–Carpathian foredeep. More specifically, it occupies the steep northwestern slope of the incised meander spur, which forms an ~ 800-m-long rocky promontory of the Větrník hill plateau at ~ 500 m a.s.l. (Fig. 2). The slope is composed of the Bíteš orthogneiss, formed by flaser, leucocratic two-mica gneiss (Ivan and Kirchner 1994). Metamorphic foliation dips 15–30° NW in general (Ivan and Kirchner 1994). The mean inclination of the failed slope oscillates at approximately 25° (Košťák 2001) but locally exceeds 55° (Demek 1996). Joint systems strike in the NW–SE, WSW–ESE and NNE–SSW directions, which is also reflected by the shape of the river meanders (Zvelebil et al. 1996). The LR is not the only slope failure described within the wider area (Hrádek 1998), but with its complexity, it remains unique. Except for typical gravitational features such as undulated terrain with rock scarps or scree slopes, it reveals distinct 100-m-long and 25-m-high fault-predisposed rock wall (locally named the Main Trench) in its upper portion, sagged and rotated rock blocks Fig. 1 Simplified geological map of the Alpine–Carpathian–Bohemian Massif junction area (based on Špaček et al. 2015) with the geological setting of the Dyje Window. LR, the Ledové sluje rockslide; DCFZ, Diendorf-Čebín Fault Zone 1707 1707 Landslides 20 • (2023) (locally named Pillar I and Pillar II) and pseudokarst caves (both crevice and boulder types) (Figs. 3 and 4). Cave openings along the Main Trench as well as within the pillars and scree accumulations have been described since the nineteenth century (Kopecký 1996). Even though caves reveal complicated morphology, the main direction of their crevice-type corridors (NE–SW) is parallel to the main fault scarp strike. Other shorter cave corridors follow NW–SE or NNW–SSE directions (Kopecký 1996). Until 1996, speleologists documented 7 caves within Pillar I with cumulative length up to 100 m and elevation change up to 20 m and 7 caves within Pillar II with the length more than 400 m and elevation change up to 30 m (Kopecký 1996) (Fig. 3). Wagner (2001) described 17 caves. He highlighted that some individual underground crevices are 10 m high. Overall, the caves reveal the typical morphology described earlier by Lenart (2015) and Margielewski and Urban (2017) from the Outer Western Carpathians. Individual caves are interconnected through widened joints by visible connection or at least by air draft. Rock surfaces within the caves are covered or impregnated by opal, silicate, phosphate or gypsum coatings (Cílek 1993). Some of the caves are iced during the cold season, which further supports high vertical disruption of the rockslide structure. It is symptomatic that the icing of the caves gave the name of the whole rockslide (Ledové sluje (Cze.) = ice caves). From time to time, rock falls are observed (Košťák 2001), both on the surface and inside caves. Methods Geomorphic mapping Geomorphic mapping was focused on landforms related to slope failures, and it was conducted by surface GNSS mapping and speleological surveys inside the crevice-type caves. Geomorphological interpretation was based on the high-resolution LiDAR-derived digital terrain model of the Czech Republic provided by the State Administration of Land Surveying and Cadastre (DMR5G) with a spatial resolution of 1 m and the maximum error in altitude reaching 0.3 m in forested areas. A detailed topographic map at a scale of 1:5 000 was used as the main source for surface mapping, which helped to delimit slope failure and reveal distinct landslide features in the study area. The existing results of geomorphological mapping, research and inventories by Ivan and Kirchner (1994) and Demek and Kopecký (1996), were also considered. Detailed geomorphological maps at scales of 1:5 000 (Demek and Kopecký 1999) and 1:200 (Počta and Schönbeková 1991) served as basic sources for a better understanding of the wider spatial context of the rockslide area. Cave maps obtained earlier by speleologists were used for orientation in CTCs. Within them, we used tape for the identification of vertical shifts indicating sagging of blocks. Structural analysis and movement mechanism The rock surfaces exposed mainly within the CTCs were investigated by structural analysis. The methodology by Margielewski and Urban (2003) was used to determine the mass movement types that formed the rockslide. This method relies on the fact that changes in the dip and direction of discontinuities between in situ rock masses and gravitationally shifted blocks reveal the type of local gravitational movement, i.e. translation, toppling or horizontal and vertical rotations of rock packets (sensu Dikau et al. 1996). This assumption is valid only in spatially limited slope sections (~ 101 m) and for rock masses not affected by folding. Measured in dip direction/dip angle format for planes and trend/plunge format for lines, structural data of faults, fractures and foliation planes have been visualized as contour diagrams in the lower hemisphere of the Lambert equal area projection. Electrical resistivity tomography The geoelectrical properties of the rock massif were examined by means of a multielectrode resistivity measurement technique, i.e. electrical resistivity tomography (ERT). The survey was conducted to reveal the internal structure of the main scarp area of the studied rockslide. Measurements are based on direct current passing through a pair of electrodes grounded to the subsurface and on measured potentials on a pair of potential electrodes (Milsom and Eriksen 2011). According to Ohm’s law and the geometric factor Fig. 2 The Ledové sluje rockslide (delimited by orange arrows) and the Thaya River canyon. Visualization is based on the DMR5G digital elevation model (ČÚZK) with 1-m resolution. Pillars I and II are shown in more detail in Fig. 3 1708 1708 Landslides 20 • (2023) Technical Note (k coefficient), the apparent resistivity (ρa) is then calculated and further recalculated into real resistivity (ρ) by means of an inversion procedure in Res2Dinv software (Loke and Barker 1996). The resulting inverted models are depicted as resistivity sections. Two ERT sections were measured using a multielectrode system ARES (GF Instruments, Czechia). Both profiles were conducted in a Wenner-Schlumberger array with a 5-m electrode spacing. Section P1 was 165 m long, and Section P2 was 185 m long. Surface exposure dating Terrestrial cosmogenic nuclide (TCN) dating using 10Be was used to determine the minimum age of the main 15-m-high scarp of the rockslide. The method is based on a concentration measurement of in situ produced cosmogenic nuclides that builds up in the mineral’s lattice from interactions occurring between the target mineral and particles arising from secondary cosmic ray flux (for Fig. 3 Detailed geomorphology of the most distinct portion of the Ledové sluje rockslide (after Počta and Schönbeková 1991) with caves, cross-sections (after Zvelebil et al. 1996) and ERT Section P1 with stationing. 10Be, position of TCN dating profile; TM, positions of extensometric measurements (Košťák 2001) 1709 1709 Landslides 20 • (2023) further details, see, e.g. Ivy-Ochs and Kober 2008). Recently, dated landslide scarps testified to the usefulness of this dating strategy for determining the timing of scarp exposure (e.g. Le Roux et al. 2009; Zerathe et al. 2014; Schwartz et al. 2017). Samples for 10Be dating were taken from the nearly vertical main scarp with minimal evidence of secondary rockfalls, subsequent weathering and postfailure erosion in general. For assessment of different phases of possible slowly moving rockslide, a total of four rock samples placed one above the other along the transect on the subvertical scarp surface were obtained (Fig. 4a). All samples were crushed, sieved and cleaned with a mixture of HCl and H2SiF6. The extraction method (Braucher et al. 2000; Merchel and Bremser 2004) for 10Be involves isolation and purification of quartz and elimination of atmospheric 10Be. Exactly 150 µl of a (3025 ± 9) ppm 9Be solution was added to the decontaminated quartz. Beryllium was subsequently separated from the solution by successive anionic and cationic resin extractions (DOWEX 1X8 then 50WX8) and precipitations. The final precipitates were dried and heated at 800 °C to obtain BeO and finally mixed with niobium powder prior to measurements, which were performed at the French AMS National Facility, ASTER, located at CEREGE in Aix-en-Provence. Beryllium data were calibrated directly against the STD11 standard (Braucher et al. 2015) with a 10Be/9Be ratio of (1.191 ± 0.013) × 10−11. Analytical uncertainties (reported as 1σ) include uncertainties associated with AMS counting statistics, AMS external error (0.5% for 10Be) and chemical blank measurement. A sea-level high-latitude spallation production rate of 4.02 ± 0.32 at. g–1 a–1 (Borchers et al. 2016) was used and scaled using Stone (2000) polynomials. The general equation used to model 10Be concentrations considering the three types of particles involved is given by Eq. 1: where Pn., Pstop. and Pfast are the production of neutrons, stopping and fast muons, respectively; ρ is the material density; ε is the denudation rate; t is time; and Λneut and Λstop. and Λfast are the attenuation lengths of neutrons (150 g/cm2), stopping (1500 g/ cm2) and fast muons (4320 g/cm2), respectively. λ is the radioactive decay constant (λ = ln2/half-life). x is the depth before the sliding event (after the sliding event, samples are exposed at the surface). (1) N (0,𝜀,t)= Pn.e−𝜌x Λn. ( 1−e(-t(𝜌𝜀 Λn+𝜆)) ) 𝜌𝜀 Λn +𝜆 + Pslow.e−𝜌x Λslow .(1−e-t(𝜌𝜀 Λslow +𝜆) ) 𝜌𝜀 Λslow +𝜆 + Pfast.e−𝜌x Λfast .(1−e-t(𝜌𝜀 Λfast +𝜆)) 𝜌𝜀 Λfast +𝜆 +N( x ,𝜀,∞).e −𝜆t Fig. 4 Morphology of the most distinct portion of the Ledové sluje rockslide. a The main scarp with positions of rock sampling for TCN dating; b the main scarp above the Main Trench filled with blocks; c the highly disrupted front of Pillar II with the entry into the Brněnská crevicetype cave; d the interior of the Brněnská crevice-type cave with typical rectangular corridors filled with wedged blocks; e narrow crevice in Brněnská cave with apparent vertical shift of the opposite blocks indicating sagging. See Fig. 3 for the TCN dating profile position and names of individual caves 1710 1710 Landslides 20 • (2023) Technical Note The muon contribution scheme follows Braucher et al. (2011). Topographic shielding was determined using Dunne et al. (1999). The term N(x,𝜀,∞) is the inheritance coming from a previous exposure at depth and assuming steady state (T = infinite) and with a denudation ε. This denudation ε is a local long-term denudation rate determined using the top reference samples not affected by the sliding event. The age calculation was therefore a three-step calculation: (i) determination of the long-term denudation rate with the top sample (LS0); (ii) estimation of the inheritance at depth of samples below LS0 assuming the denudation rate determined above; and (iii) determination of the exposure ages after the sliding event considering inheritance determined in step 2. Results Geomorphology and structural setting of the rockslide The LR occupies an area of ~ 0.1 km2, with a topographic relief of ~ 150 m. It reveals fresh topography. The upper easternmost portion reveals a typical scarp with a linear and transversely asymmetrical shallow depression/graben separating the rockslide from Větrník Hill (Fig. 2). The northern branch of the failure is topographically rather indistinct, except for Pillar I, revealing rock walls and rock towers highly disrupted by a system of open fissures and CTCs (Fig. 3). There, the original rock structure is strongly overprinted by varied secondary failures — rock falls, slides and rotations. Below Pillar I, the slope is covered by scree accumulation. The southern branch of the LR is very distinct. From the Ledové sluje ridge, Pillar II is separated by the gravitational trench (the Main Trench) bounded by vertical rock walls or steeply declining scree piles (Fig. 3). Downslope, NE–SW elongated deep opened fissures and CTCs separate blocks of the failed rock mass. Pillar I culminates with a highly disrupted northwestern rock face with the entrances into the largest CTC — the Brněnská cave (length ~ 400 m). The lower part of the slope is covered by scree cover. Overall, the foot of the LR lacks a distinct toe due to the erosion of the Thaya River that shaped the formerly incised meander (Fig. 2). Viewed from the caves, we found that the orthogneiss rock mass was highly heterogenous. In addition to joints and faults, we detected subvertical mineral veins (~ 101 cm thickness) and subhorizontal intercalations (~ 101 cm). Additionally, weak, weathered and eroded layers (~ 5–13 cm thick) permeating the massif equate to biotitic paragneiss inclined 2–4° within the overdip slope (sensu Meentemeyer and Moody 2000), earlier described by Košťák (2001). Tectonic features such as Riedel shears, plumose structures, tectonic mirrors and striations were observed on rock walls. The main structural control of the rock massif (Fig. 5) corresponds mainly to NEto ENE-striking steep fractures and faults, predominantly facing the SE (contour maximum density 145/83). Metamorphic foliation gently dips towards the NW (maximum 300/5). Identified mainly on the basis of striation surfaces and tectonic mirrors, faults are characterized primarily by ENE-striking (maximum 334/83) and secondarily also WNW-striking (197/86) structures with SW-oriented striations with dip range 30–80° (maximum 240/63). The eight CTCs (the Ananas, Grotte 1, Grotte 2, Netopýří, Sintrová, Pod schodištěm, Nová and Brněnská Caves) and the Main Trench were analysed based on changes in the anisotropy of upslope and downslope rock blocks. The structural assessment avoided sites with locally folded orthogneisses since their anisotropy is attributed to continuous tectonic strain in rocks, not to rigid deformation formed by slope failure. The extensive structural analysis of upslope and downslope blocks enabled the identification of translated and rotated blocks within the rockslide body. The structural sketch showing the foliation within all analysed sites is shown in Fig. 6. Recalculated into apparent dips, the representative foliation planes are also depicted in the NW–SE-directed pseudosection (Fig. 6). The translated blocks exert identical fabric with foliation planes dipping gently to the NW (300/5). The rotated structures are characterized mainly as back-rotated, with foliation dipping SE up to 11° (except the Grotte 1 Cave), while toppled blocks dip to NW up to 16–22° (the Nová, Ananas, Brněnská Caves). Resistivity imaging Figure 7 shows the measured ERT profiles and their locations within the LR area. Absolute values of resistivity of both sections were strongly influenced by highly resistive orthogneiss. The P1 section oriented in the NW–SE direction was measured across the main ridge above the Main Trench downwards behind the lowermost known crevices of the Brněnská Cave. The most striking feature of the P1 section is represented by the high resistivity domain at stationing ca. 70–100 m, exceeding 10,000 Ω·m. It is interpreted as a relatively fresh compact rock mass exposed by the main scarp of the rockslide with a near-surface zone of distinct resistivity variations. From SE at stationing ca. 90 m, it is bordered by a sharp resistive transition steeply dipping towards the SE, which is interpreted as a fault structure predisposing the Main Trench. Down the slope, up to ~ 12-m-thick surface domain of relatively low resistivity (< 3000 Ω·m) may be tracked at stationing 25–65 m, acting as a relaxed part of the rock massif with slided blocks separated by crevices. Oriented SW–NE, the P2 section runs parallel to the Main Trench and further upwards through the N–S-directed shallow trench. The profile clearly captured its subsurface structure and documents gravitational breakup of the highest portion of the rockslide. The subhorizontal zone of reduced resistivities (< 600 Ω·m) is well pronounced at stationing from ca. 65 m onwards with a base situated 15 m deep. This domain propagates up to the surface at stationing 80–100 m, corresponding with the expressive topographic response of the gravitational trench. Dating All dated samples from the 15-m-high rock wall of the main rock scarp show Late Pleistocene exposure ages, specifically falling in the younger half of the Last Glacial period (Tables 1 and 2). The uppermost sample LS1 yields an age of 42.6 ± 4.4 ka, the middle sample LS2 yields an age of 26.6 ± 3 ka, and the lowermost sample LS3 reveals an age of 23.4 ± 2.7 ka. As the ages decrease from the top to the bottom, the rockslide formed due to slow gradual or multievent displacement over tens of thousands of years rather than during a single catastrophic event. 1711 1711 Landslides 20 • (2023) Discussion Causes and triggers of the rockslide The Ledové sluje rockslide belongs to the most explored slope failures in Central Europe with a long tradition of investigation. The authors of the first descriptive studies outlined the crucial triggering role of the Thaya River undercutting the slope (Filek 1895; Špalek 1935). As summarized by Demek (1996), various authors also mentioned the crucial role of weak biotitic paragneiss intercalations and Pleistocene frost weathering as predisposing and preparatory factors. Kopecký (1996) underlined the influence of local folding and jointing. Our investigation also revealed other potential geological predispositions of slope instability — subvertical mineral veins. Based on the analysis of nearly 3000 structural measurements, we determined the overall pattern of steep NEto ENE-striked fractures and faults protruding into a highly incoherent rock massif. A similar structural pattern was previously described by Zvelebil et al. (1996), who also pointed out the significance of NWand NNE-trending fracture sets. NE-striking structures are developed longitudinally with respect to the strike of gently dipping foliation planes. Pospíšil and Pazdírek (1998) highlighted the importance of NW-trending fractures and faults, which was also supported by the study of regional fracture pattern (Pospíšil et al. 1997). They found the transverse NW-directed fabric to be the main predisposition that enabled the development of longitudinal fissures and therefore the subsequent evolution of the rockslide. Such a structural setting of the rock massif, together with the position of the rockslide predominantly on a NW-oriented overdip slope (sensu Meentemeyer and Moody 2000), defines the main predisposing factors for the development of LR and respective CTCs. As summarized by Ivan and Kirchner (1994), undercutting caused by the former Thaya River course remains the suspicious triggering factor. As a result of the DEM visualization (Fig. 2), the foot of the LR is obviously eroded, and the accumulation part is Fig. 5 The results of structural analysis reveal mutual relations between upslope (black diagrams) and downslope (red diagrams) rock blocks, predisposition and types of slope movement, number of measured faults and striations (n), fractures (nf) and foliation planes (nb) 1712 1712 Landslides 20 • (2023) Technical Note apparently missing. Based on ground penetrating radar profiles, Hubatka (2001) revealed a former channel within the incised meander buried beneath a 20–30-m-thick cover of colluvial deposits at the foot of the rockslide. In contrast, Zvelebil et al. (1996) assumed tectonic impulse for at least the initial evolution stages of the LR. Pospíšil and Pazdírek (1998) also mentioned the importance of a seismic factor, although without providing any clear evidence. The proximity of the DCFZ has often been argued to support the hypothesis of a seismic trigger. The southern section of the DCFZ near Krems and Melk in Austria is characterized by weak recent seismicity with an estimated maximum magnitude Mw ~ 3.5 (Lenhardt et al. 2007; Špaček 2021). The Ried am Riederberg earthquake in 1590, known as the strongest historical earthquake in Austria with an estimated magnitude Mw ~ 5.8 and an epicentral intensity of 9° EMS-98 (Hammerl and Lenhardt 2013; Hammerl 2017), is located ~ 70 km from the LR site. A few instrumentally or macroseismically recorded earthquakes are also known from less distant areas (< 30 km from the LR site), e.g. from Hostěradice (ML = 2.5; years 2000 and 2014), Božice (ML = 1.4; year 2006) or Ctidružice (ML = 0.9; year 2018; ~ 10 km from the LR site; Špaček 2021). However, these earthquakes appear to be too weak to trigger a coherent deep-seated rockslide, generally requiring M > 4.5–5 (Murphy 2015). Subsurface structure of the rockslide Joint interpretation of outcrop and geophysical data can significantly improve the understanding of the internal structure of the rock mass (Place et al. 2016; Lesage et al. 2019; Müller et al. 2020). Likewise, structural analysis can enhance the interpretation of geophysical data characterizing mass movement features (Břežný et al. 2018; Chalupa et al. 2018; Tábořík et al. 2017), even much better if performed in CTCs. However, due to the rare occurrence of accessible CTCs in landslide terrains, such studies are sparse (Pánek et al. 2010). The studied rockslide is characterized by a series of disrupted slided blocks separated from each other by fractures and crevices or within its upper part by topographically distinctive gravitational trenches, which clearly correlate with relatively low-resistivity or high-gradient domains of the resistivity sections (Fig. 7). However, high resistivity values represent a coherent rock massif without fracturing that was exposed by the main scarp of the rockslide. The contrasting resistivity response resembles the geophysical image described by Heincke et al. (2010) from similar conditions of the Åknes rockslide developed in gneissic rocks in Norway. Based on an integrated 3D geophysical survey, the authors have shown that similar high resistivity zones (> 17,500 Ω·m) can be assigned to intact and unfractured rock masses with low water content. Fig. 6 Top, structural map revealing the geometry of translated (black marks) and rotated (red marks) rock blocks within the rockslide body; bottom, NW–SE-oriented reference pseudosection indicating the clustering of the rotated blocks with respect to the translated blocks. See the reference section above 1713 1713 Landslides 20 • (2023) Neither of the two P1 and P2 profiles revealed a distinct sliding surface (Fig. 7). However, the topmost sliding surface is expected to occur at depths of 12–15 m based on the interpretation of resistivity Section P1. Within the P2 section, the sliding surface that probably enabled the evolution of the distinct N–S trending trench could be 20 m deep. The previous geoelectric surveys conducted by Pospíšil and Pazdírek (1998) and Hubatka (2001) indicated the disruption of the rock massif to depths over 35 m and the occurrence of the Fig. 7 ERT sections P1 and P2 and their locations within the rockslide Table 1 Measured sample properties. The depth is the vertical distance from the sample to the top of the scarp. The shielding is the actual topographic shielding. See Fig. 4 for the locations of the samples Sample Depth (cm) Shielding Mass quartz 9Be added 10Be/9Be Uncertainty 10Be (at/g) 10Be uncertainty (at/g) LS0 0 0.709 15.5213 3.137E + 19 8.59300E-14 8.1200 169 381 13 754 LS1 500 0.487 19.8964 3.248E + 19 5.67016E-14 6.4000 89 099 5 702 LS2 950 0.487 22.5354 3.135E + 19 5.00084E-14 7.7011 66 612 5 130 LS3 1450 0.452 24.9253 3.234E + 19 4.42379E-14 7.9844 54 640 4 363 Blank - - - 3.153E + 19 2.12776E-15 17.4937 - -